Kotobukiya 1/10 Takanashi Koyomi (Swimsuit) japan NEW

Plastic Assembled Figure Kit Pure white one-piece swimsuit is neat! Koyogi Kotoyu is wearing a swimsuit following her school uniform. The simple one-piece swimsuit is accented with a ribbon at the chest. The back has a bold design with a cross back. Her straw hat with a large ribbon and high-heeled sandals are partially pre-painted and color-coded. She comes with a sitting poseable body and fixed leg parts for natural posing. Points of Attention Movable neck joint]. The ball-jointed neck slides forward and backward, allowing you to pose her looking up or pulling her chin down more naturally than ever before. Body for sitting pose]. The body for Koyomi's sitting pose is based on the theme of "sitting on a chair" or "sitting on a flat surface". The body is designed to look like it is sitting on a chair, or sitting flat on the floor. Fixed leg parts and special stand In addition to the sitting body, the fixed leg parts allow the figure to be posed with knees bent deeper than when using the movable parts. The fixed leg parts can be replaced from the movable thigh roll part, so you can expand the range of poses by using only one leg as a fixed leg part. She can also be displayed in a crouched position by using the body for a seated pose, fixed leg parts, and a dedicated stand. The stand is molded in clear colorless plastic. Newly sculpted hand parts. Newly sculpted wrist parts with a gentle hand expression. The hand parts allow for a variety of poses, such as blocking out the summer sun or placing small objects in the palm of the hand. Clear molded bracelet. The bracelet she wears on her left hand is molded in a clear blue color, and a fine lame material has been added to give it a beautiful finish. [Painted parts] Pre-painted parts are used for her sandals and the ribbon on her straw hat, so simply assemble the figure to create a finished product that is close to the finished sample. Four expressions are included. A newly sculpted "winking face", "staring face", "tongue-tied face" and a smiling face in summer clothes are all included, allowing you to create a variety of different expressions. Barefoot parts are included. She comes with both sandal and barefoot ankle parts. The barefoot type can be used in a normal standing pose, as well as with her toes curled or bowed to create a variety of different expressions. Glasses and exclusive forelock parts She comes with two types of eyeglass parts, one with and one without glasses. She also comes with two types of bangs, one with and one without glasses, allowing you to choose whether to display her with or without her glasses. Three bangs parts are included for each figure. The glasses parts are clear and colorless. To reproduce the finished model, you will need to paint them yourself. Clear blue base for display. The display base will be a clear blue color, which is based on the image of the waterfront. Accessories 1) Kiku Koyu body x 1 set 2) 3 hairstyle parts Bob cut", "Half up" and "Braid" x 1 set each 3)Forelock parts without glasses x 3 4) Attachment parts for arranging bangs x 1 5)Pre-painted expression parts: [winking face], [glazed face], [tongue protruding] and [smiling face (mouth open)] x 1 each 6)Unpainted expression parts: [winking face], [stern expression], [tongue protruding] and [smiling face (mouth open)] x 1 each 7) Straw Hat x 1 set 8) Glasses parts x 3 9)Folded glasses parts x 1 10)8 kinds of wrist parts: "Normal handle", "Narrow handle", "Wide handle", "Round handle", "Grip hand", "Pointing hand", "Flat hand A", "Supporting hand" x 1 for each left and right 11) Body for sitting posture x 1 set 12)Fixed leg parts x 1 set (for left and right) 13)Bare foot parts [Normal], [Fingers rounded] and [Fingers bowed] for each left and right side 14)Megami Device compatible 6mm diameter neck parts x 1 15)Display base x 1 set 16)Water transfer expression decal x 1 sheet (C) KOTOBUKIYA ----- Works Sosai Shoujo Teien Series Character Plastic Model Scale 1/10 Product Size Height: approx. 160mm Product Specifications Plastic model Number of Parts 201-400 Material PS, ABS, POM, PVC (non-phthalate) Design Yunosuke Maruke The image is a prototype. It may differ slightly from the actual product. Also, it has been painted for the purpose of photography. (From Kotobukiya website)