HI Q PARTS Sanding tip 70 # 1000 (1 piece)
Special Price
¥216
Regular Price
¥240
Out of stock
SKU
HIQ72977
You will earn 10 Points for writing a review this product. You will earn 6 Points for purchasing this product.Stick filing, sand paper and so on.
Graininess Printed PET plate pasted paper file
A tool for sandpaper which puts paper file on PET board.
If it is a modeler with a long history of modeling, it is theory to paste it on a plaque or the like by himself and make a self-fabricating file of a file for a fine file, but this product is affixed to the board in advance, You can start working immediately with it, and it is the best for beginners.
On the PET board, the count (grain size) has been finely printed and there is no case that I do not know the count even when cutting it finely with scissors.
The thickness of the sanding tip 70 is about 0.7 mm.
It is useful for sandpaper in places where recessed parts are scratched and metal filings put too much force.
Responding to water sharpening.
Size 56 mm x 114 mm
made in Japan
Supplement
To increase the new likes of the plastic model
When explaining from friends who are interested in plastic model to "fileing → painting", it is a method of fileing in fine parts that was personally becoming a neck.
"Put the paper file on the platter board, cut it with scissors, write it on the reverse side, write the count on the back, I hope the fine details should be squished!" For those who have gotten used to a certain extent, and the troublesome Yes.
So, in detail, I wanted to cut this "sanding tip" with scissors.
Instead of cost performance, tools that can be easily started first are important.
I do not know the count
If possible, I would like all sandpaper to be so, but I turned out to print the whole number because I do not know the count (granularity) when cutting.
Perhaps I think that it is not supposed to cut as much as the original paper file itself in a plastic model.
In this "chip", I print large counts and small counts all seen in the tool box even when I see it.
For those with a fine count, I tried the test several times and it was the best tilt I did not lose sight of the count when the print that was tilted by 15 degrees was small.
Moreover, while it rubs with your fingers, it also has a strong coating so that the printing will not be bald.
Graininess Printed PET plate pasted paper file
A tool for sandpaper which puts paper file on PET board.
If it is a modeler with a long history of modeling, it is theory to paste it on a plaque or the like by himself and make a self-fabricating file of a file for a fine file, but this product is affixed to the board in advance, You can start working immediately with it, and it is the best for beginners.
On the PET board, the count (grain size) has been finely printed and there is no case that I do not know the count even when cutting it finely with scissors.
The thickness of the sanding tip 70 is about 0.7 mm.
It is useful for sandpaper in places where recessed parts are scratched and metal filings put too much force.
Responding to water sharpening.
Size 56 mm x 114 mm
made in Japan
Supplement
To increase the new likes of the plastic model
When explaining from friends who are interested in plastic model to "fileing → painting", it is a method of fileing in fine parts that was personally becoming a neck.
"Put the paper file on the platter board, cut it with scissors, write it on the reverse side, write the count on the back, I hope the fine details should be squished!" For those who have gotten used to a certain extent, and the troublesome Yes.
So, in detail, I wanted to cut this "sanding tip" with scissors.
Instead of cost performance, tools that can be easily started first are important.
I do not know the count
If possible, I would like all sandpaper to be so, but I turned out to print the whole number because I do not know the count (granularity) when cutting.
Perhaps I think that it is not supposed to cut as much as the original paper file itself in a plastic model.
In this "chip", I print large counts and small counts all seen in the tool box even when I see it.
For those with a fine count, I tried the test several times and it was the best tilt I did not lose sight of the count when the print that was tilted by 15 degrees was small.
Moreover, while it rubs with your fingers, it also has a strong coating so that the printing will not be bald.
| Release Date | Dec 15, 2017 |
|---|---|
| Package Depth (mm) | 100 |
| Package Height (mm) | 70 |
| Package Width (mm) | 20 |
Write Your Own Review